MAG box problems: STB blocked and page loading errors
Fix the common MAG box errors: STB blocked, black screen, page loading error, and a loading bar that stays stuck.
Updated November 14, 2026 4 min read
MAG boxes show a few specific errors. The most common error messages are:
- STB blocked, or a black screen
- Page Loading Error
- A loading bar that stays stuck
This article explains how to solve each of them. If you are setting up the box for the first time, start with how to set up IPTV on a MAG box.
STB blocked (black screen)
STB blocked on a MAG box happens for several reasons. This section explains all of them.
Note: On some MAG boxes you see only a black screen instead of the STB blocked error message.
The MAC address was not added to the subscription or was removed
For a MAG box, you must add the box MAC address to the IPTV subscription. Read what a MAG box is for background on the device.
Many IPTV providers give you a dashboard where you can edit your subscription. In the dashboard you can add the MAC address or check that it is still on the subscription. If you do not have a dashboard, contact your IPTV provider about this.
A wrong MAC address was added
If you add a wrong MAC address to your IPTV dashboard by mistake, there is a 100% chance that you will see this error on your screen. Check every character and number that you entered against the label on the back of your MAG device.
The line expired
If your IPTV subscription has expired, you see the STB blocked error or a black screen. Open your IPTV dashboard, check whether the subscription has expired, and extend the line if it has.
The line is disabled
IPTV providers disable subscriptions that are used on more devices at the same time than the subscription allows. Ask your IPTV service whether the line has been blocked.
ISP blockage
ISP blockage is another reason for the STB blocked error or a black screen. Contact your Internet Service Provider and ask for more information. You can also try another internet connection, such as a 4G connection from your phone, to confirm the cause.
The last solution for ISP blockage is a reliable VPN service. Note that a MAG box needs a special router to run a VPN.
A wrong portal address was added
A wrong portal address in the MAG box produces this error for the same reason as a wrong MAC address, with a 100% chance that you will see it again. Ask your IPTV provider for the correct portal address, then add it to your MAG device. Read how to change the portal address on a MAG box.
Page loading error
This error mostly occurs because the internet connection is not working properly.
On the Page Loading Error screen, the box reports Ethernet Link: UP when everything is fine, or DOWN when the Ethernet port is not connected to the router. Your internet connection may also be working poorly, so check whether internet access is available.
How to fix the page loading error
The set-top box needs a working internet connection. Start with the cable between the box and the router.
- Check that the Ethernet cable between the set-top box and the router is plugged in at both ends.
- Check that the LAN light on the router port that connects to the back of the set-top box is lit.
- Check the connection on the back of the set-top box. Two lights should be on where the cable is plugged in, one orange and the other green.
- Replace the Ethernet cable if the light on the router or the lights on the box do not come on. A light that stays off means there is a connection problem.
- If the problem continues, unplug the power cables from both the router and the set-top box.
- Plug the router power cable back in.
- Wait two minutes, then plug in the set-top box power cable.
When the router and the box are in different rooms
If your router is in one room and the set-top box is in another room, connected to the router through an Ethernet line, check the lights on the sockets. If a light is not on, the power line has lost its wireless connection to the router. Reboot the router, then reboot the power line. When the light is back, reboot the set-top box too.
If the light is on and the box is still stuck on the loading screen, make sure that the power line has the LAN light on the front.
Loading bar stuck on the MAG box
Sometimes a loading message appears on the screen when you try to switch channels. Reboot both the modem and the set-top box to fix it.
More in Troubleshooting
Still stuck?
Our support team can help you set up your device or fix a problem.